Shanghai Venttech Refrigeration Equipment Co., Ltd.  

Product Name: New Conditions Floorstanding Air Dry Refrigeration Cooler Model NO.: SHSL-D2-601-14X630F24 Condition: New Certification: RoHS, ISO Application Fields: Machinery Noise Level: Low Fans Species: Double-speed fan System Type: Open System Cooling Water: Industrial Water Type: Air-Cooled Product Name: New Conditions Floorstanding Air Dry Refrigeration Cooling Capacity: 394kw Water Flow: 60L/Sec Fan Quantity: 14PCS Power Supply: 400V-3pH-50Hz Total Motor Power: 38.5kw Inlet/Outlet Connection: Dn125 Inlet Air Temperature: 20 Degree C Inlet/Outlet Water Temperature: 35/25 Degree C Trademark: VENTTK Transport Package: Wrap Film/Pallet Specification: refrigerant unit Origin: China HS Code: 8415901000 Product Description New conditions Floorstanding air dry refrigeration coolerDry Coolers are widely used in refrigeration, air-conditioning, food processing, heating plants and power plants.General productions:Suitable environmentDry Cooler series:D1and D2 series.Environment temperature: 35ºC.Air does not contain chemical substances, corrosive gasses and dust-free;Please specify requirements for explosion-proof upon order Design Conditions: Design pressure 2.0MPa;Test pressure2.5MPa Medium: WATER Working conditions:EnvironmentSpecificationsAmbientTemperature35ºC, Inlet Temperature48 ºC,Outlet Temperature39 ºC D4 SeriesDetails:SignNameFunctionAStandFix equipmentBmetalSheet CasingGalvanized Steel Coated CasingCCooling CoilAl Fin and Copper TubeDFanLow Energy consumption fan to maximize air flow and low noiseOrder No.PJO-2016SHSL08145Product nameDry CoolerModelSHSL-D4-362-6X910F1Order quantity1Gist: JB/T 7659.5-1995Inspection item Processing quality Processing qualityAir pressure testInsulation resistanceElectric strengthWhole set of productsNameplate and factory fileDetermineItem numberCOIL LengthL≤1000(±2mm)L>1000(±4mm)COILDiagonalD≤1000(±3mm)D>1000(±5mm)Fin patternFin: conform to the requirements, no burr, no Rip, no pour, no dew copper, no wrinkles, no burning out.Sheet metal: no scratches and deformation, surface should be clean, smooth, colours and luster is consistent, uniform coating.With ≥1.15 times design pressure totest, no leakage and deformation. Design value:2.5MPaElectric parts to ground ,to the charged metal parts of the insulation resistance(cold)≥2MΩ1800V voltage,keep one minute, no puncture ,no flashoverInlet and outlet connectors;flange ,fan,electric heating tube bracket,valves and so on.content is complete,same with the good, factory file is complete, the specification is correct2016D08145-0013300/33033300/33043672/36753675/3675Aluminumfin 0.115mm,2.2mm/RippleAccordAccord10min/2.5MPaNonOAccordAccordQualifiedSite assessmentSelected installation site must meet the following requirements:Level Ground;Ground or Floor strength able to support the wedight of equipment;no obstructions at air outlet.Upon confirming above conditions, take the following installation steps. Forklift or lifting product out of wooden pallets, loosen transport screw at stand and tighten after raising the screws to same horizontal plane as product. After moving product to the predetermined location, bolt tightly with large washer and spring washer. WarningMinimize bias and ensure the level of the product during installation.Ensure tubes level and no loosen parts in dry coolerDuring installation, avoid weight of pipeline on the dry coolers. WiringPower requirements: Axial Fan power wiring: Axial fans are often using one phase or 3 phase motor. The 3 phase motor has two configuration, Y-shape and △ShapeFan motor should have reliable power supply equipped with over voltage, under voltage and over current protection. Each fan is equipped with current protection settings. Internal thermal protection devise should be connected to the control lines to prevent damage to the motor due to over voltage, under voltage, lack of phase, contact failure. Motor wiring shall be installed according to the requirements when using two-speed motor. warningMotor overcurrent protection and built in thermal protection settings must be connected. Electrical connections must be completed by qualified professionalsEnsure wiring are correct and accurate to prevent motor failureElectrical InstallationWarningEquipment installation must be done by qualified personnel Ensure all electrical circuits are installed in accordance GB 8877-88(household appliances installation, use, maintenance and safety requirements) or any other local regulations Equipment shall be safely grounded with resistance less than 2ΩEnsure all fan connecting cables are according to required standards of fan manufacturers. Equipment commissioning4.1 power on check Check to ensure all requirements above are met. All requirements is to be met before trial run. Ensure all accessories are installed securely before powering on. 4.2 Power supply checkEnsure voltage and power supply matches name plate by measuring equipment and is safely grounded with less than 2ohm before power up. 4.3 Trial OperationEnsure each fan is tighten and is not obstructed prior to commissioning. Rotation of the motor must be accordance with the factory specification. Ensure no jamming and free rotation to fan and motor.Photos show: